Entegra Condensation
Condensation is something that may occur in the Entegra products, this is due to humidity and temperature. Once the Entegra system is powered on, the heat generated by the Entegra system will clear the condensation. Avidyne does not RMA the Entegra units for condensation, as we do not seal the screens to its hous…
Entegra EX5000 MFD Not Enough Space
Dealers, If you are loading Jeppesen Charts and the MFD shows you the message; Not enough space. This is due to the size of the charts you are adding to the MFD. The Compact Flash (CF) card installed in the MFD is possibly 512MB, and will need to be updated to the 2GB compact flash card. Pilots/owners will need to w…
MFD Configuration - port conflict
What to do when getting a port conflict during the MFD configuration: 1 - Confirm the port settings (manufacturing settings (Piper, Cirrus, etc.), recorded settings taken prior to updating the unit) 2 - Select the senor with the incorrect setting 3 - Change setting to the correct port 4 - Save 5 - Check System…
Entegra EX5000 MFD Exceedance Message
Pilots with Exceedance messages on the MFD must work with a Piper Distribution Service Administrator (DSA) to remove the Exceedance message(s). Please use the attached DSA file to find the closest DSA, please note: Piper maintains this file and sites may have been moved or closed. Please call before arriving.
NEWS - AVIDYNE STREAMLINES ENTEGRA PFD/MFD SUPPORT PROCESS
NEWS July 17, 2019 AVIDYNE STREAMLINES ENTEGRA PFD/MFD SUPPORT PROCESS IN THE SPIRIT OF CONTINUOUS IMPROVEMENT Avidyne demonstrates its commitment to world-class product support and overall customer experience; Significant improvements in support processes being implemented based directly on dealer a…
EX5000 MFD Software Release P/N (Cirrus)
Cirrus - * SR20, SR22, and SRV Release 6: 530-00180-100 * Release 7.0.2: 530-00195-100 Rev02 * Release 8: 530-00195-110 Rev00 * Release 8.1: 530-00201-100 Rev00 * Release 8.1.1: 530-00201-100 Rev01 Release 8.2.2: 530-00235-100 Rev02
MFD ARINC 429 Errors
On rare occasions we may see a failure (below) where multiple errors originating from the ARINC 429 board: - Nav Source Can't Open Port (err=2) - Traffic Sensor can't connect - PFD is not communicating Check the connections and confirm the errors, contact techsupport.
How to reset fuel capacity on the MFD (Cirrus)
To change the Fuel quantity in the MFD, follow these steps: 1) power on the avionics 2) go into flight mode (accept the confirm messages) 3) using the knobs on the bottom of the unit, switch to the Aux tab 4) on the left side of the MFD you have 5 illuminated buttons; hold the top and third (L1 and L3) for approx…
Entegra EX5000 Engine config missing
While in Maintenance Mode on the MFD, if the L4 button is empty, check the software part number at the top of the page. The last three digits identify the aircraft: -000 Piper PA46, PA34 -002 Piper PA28, PA32, PA44 -100 Cirrus -200 Columbia (Lancair) -500 Aftermarket (with Radar) -502 Aftermarket (without Ra…
EX5000 MFD Software Release P/N (Piper)
Piper - * Malibu, Meridian, Matrix and Seneca V - 4 knob radar capable (Piper PA46, PA34) Release 6: 530-00180-000 * Release 7.0.2: 530-00195-000 Rev02 * Release 8: 530-00195-010 Rev00 * Release 8.1: 530-00201-000 Rev00 * Release 8.1.1: 530-00201-000 Rev01 Release 8.2.2: 530-00235-000 Rev02 * Warrior, …
